Eck I often directly as well? )))
here, as promised - post the instructions to build a pattern for the bag from the previous post:
we start from the bottom.
We need a sheet of paper (spread) throughout the length of which we will build a pattern.
Put a sheet on a hard surface fold it in half, lining up the corners and along the folds, which will be the middle pattern, starting to build.
first construct a rectangle 30 * 12. Departing from the bottom line, measure 4 cm carry perpendicular bisector fold. From the lower angle measured from the horizontal 0.5 cm and connect them with the line at 4 cm above - see bottom part of the drawing.
This bevel will allow the bag to add volume without tucks and suturing the bottom.
holds two arc diameter of 6 cm from the mid-line of 4 cm above to the extreme points of the oblique lines - look carefully drawing.
further note on the fold line 50 cm, perpendicular to spend sgibu.Otstupiv from the perpendicular, that is, the dashed horizontal line 5 cm mark on both sides of the fold to 4 cm and connect these points with the tip of the first large rectangle 30 * 12. These
same point on the line with the upper inflection point arc.
This version of the drawing is designed for sewing bags with handles, strings
In case if you need bag with a solid handle, as in the previous picture, we draw attention to the remote slice in the bottom right corner.
That is - built over the upper inflection point (Which is now on the drawing includes an arc) is still 10 cm, perpendicular to the fold and carry note from him on both sides by 3 cm
These points are connected with the points of the perpendicular fold in 4 cm and connect manually with a soft arc.
central part of the bag is placed between two such parts and resizing at will and necessity.
For example, I have a cut a rectangle 30 cm (which go to the junction with detailed pen) 20 cm (which becomes the top slice of the central rectangle). If you
need a wider-bag already - you can change the number 20 on the need - the figure is 30 remains unchanged.
When cutting parts must be aware of additional external pockets - for example, if you will open your pocket, like on my coffee bag with the previous photo, it must be cut below the main bag, and in this case you will need a rectangle 30 * 20 20 * 20 rectangle and a rectangle of lining.
Well, in general, something like that)) is ready to answer any questions ))
here, as promised - post the instructions to build a pattern for the bag from the previous post:
we start from the bottom.
We need a sheet of paper (spread) throughout the length of which we will build a pattern.
Put a sheet on a hard surface fold it in half, lining up the corners and along the folds, which will be the middle pattern, starting to build.
first construct a rectangle 30 * 12. Departing from the bottom line, measure 4 cm carry perpendicular bisector fold. From the lower angle measured from the horizontal 0.5 cm and connect them with the line at 4 cm above - see bottom part of the drawing.
This bevel will allow the bag to add volume without tucks and suturing the bottom.
holds two arc diameter of 6 cm from the mid-line of 4 cm above to the extreme points of the oblique lines - look carefully drawing.
further note on the fold line 50 cm, perpendicular to spend sgibu.Otstupiv from the perpendicular, that is, the dashed horizontal line 5 cm mark on both sides of the fold to 4 cm and connect these points with the tip of the first large rectangle 30 * 12. These
same point on the line with the upper inflection point arc.
This version of the drawing is designed for sewing bags with handles, strings
In case if you need bag with a solid handle, as in the previous picture, we draw attention to the remote slice in the bottom right corner.
That is - built over the upper inflection point (Which is now on the drawing includes an arc) is still 10 cm, perpendicular to the fold and carry note from him on both sides by 3 cm
These points are connected with the points of the perpendicular fold in 4 cm and connect manually with a soft arc.
central part of the bag is placed between two such parts and resizing at will and necessity.
For example, I have a cut a rectangle 30 cm (which go to the junction with detailed pen) 20 cm (which becomes the top slice of the central rectangle). If you
need a wider-bag already - you can change the number 20 on the need - the figure is 30 remains unchanged.
When cutting parts must be aware of additional external pockets - for example, if you will open your pocket, like on my coffee bag with the previous photo, it must be cut below the main bag, and in this case you will need a rectangle 30 * 20 20 * 20 rectangle and a rectangle of lining.
Well, in general, something like that)) is ready to answer any questions ))
